- #VIA XHCI DRIVER WINDOWS 10 VL805 INSTALL#
- #VIA XHCI DRIVER WINDOWS 10 VL805 DRIVERS#
- #VIA XHCI DRIVER WINDOWS 10 VL805 WINDOWS 8#
- #VIA XHCI DRIVER WINDOWS 10 VL805 WINDOWS 7#
So rather than throw it out, I decided to take a look at the firmware as you suggest. A reboot won't allow it to recover either. It always fails on USB 3.0 and will only run once or twice on USB 2.0 before failing there as well. The device is now no longer working for me at all, even using my little workaround. I didn't see your comments because they occurred after the bug was closed. It may take me a few days to figure it all out. I don't have too much experience recompiling a kernel and none at all applying a patch, but I'll do some research. The drive connected to this device mounts and seems to work as normal, albeit at USB 2.0 speeds. init: ureadahead-other main process (2914) terminated with status 2" EXT4-fs (sdc1): mounted filesystem with ordered data mode. sd 8:0:0:0: Assuming drive cache: write through sd 8:0:0:0: No Caching mode page present sd 8:0:0:0: Attached scsi generic sg3 type 0 scsi 8:0:0:0: Direct-Access SAMSUNG SP2514N VF10 PQ: 0 ANSI: 0 " usb 2-4: new high-speed USB device number 3 using ehci_hcd Then plugging the device into a USB 2.0 port, dmesg reads: Sudo modprobe usbcore old_scheme_first=1 use_both_schemes=0 Originally tested in kernel 3.2.0, also tested in 3.4.0, same results. Lsb_release -rd: "Description: Ubuntu 12.04 LTS The controller seems to be Prolific Technology PL2773. "Bus 002 Device 005: ID 067b:2773 Prolific Technology, Inc." Lsusb doesn't list any new devices on USB 3.0 mode, but in USB 2.0 mode:
hub 9-0:1.0: unable to enumerate USB device on port 2" usb 9-2: device not accepting address 21, error -71 usb 9-2: device not accepting address 20, error -71 usb 9-2: device not accepting address 19, error -71 usb 9-2: Device not responding to set address. " usb 9-2: Device not responding to set address. It worksįine in USB 2.0 mode, but it does not work in USB 3.0.
This is in a Vantec CB-ISATAU3, an IDE/SATA USB3.0 adapter. VIA Labs VL805 USB 3.0 Driver VIA Labs VL805 XHCI Driver VIA Labs VL805 Firmware VL805 USB 3.Cpuinfo, modules, ioports, iomem, lspci, scsi info Problems can arise when your hardware device is too old or not supported any longer. This will help if you installed an incorrect or mismatched driver. Try to set a system restore point before installing a device driver. It is highly recommended to always use the most recent driver version available. This UASP driver needs to work together with the “VIA USB 3.0 Speeder” utility.
#VIA XHCI DRIVER WINDOWS 10 VL805 INSTALL#
Please update your VIA XHCI host controller PCIe Card with latest version of firmware which can support UASP before install this driver.
#VIA XHCI DRIVER WINDOWS 10 VL805 DRIVERS#
In this driver package, it contains both the drivers for USB 3.0 host controller and UASP storage device driver. VIA USB 3.0 UASP Transfer Mode Utility 1.0.0.15
#VIA XHCI DRIVER WINDOWS 10 VL805 WINDOWS 7#
VIA USB 3.0 Hub Driver for Windows 7 (Viahub3.sys). VIA USB 3.0 Driver for Windows 7 (Xhcdrv.sys).
#VIA XHCI DRIVER WINDOWS 10 VL805 WINDOWS 8#
VIA USB 3.0 Hub Driver for Windows 8 and 8.1 (Viahub3.sys). VIA USB 3.0 Driver for Windows 8 and 8.1 (Xhcdrv.sys). Fix specific Gaming controller compatibility issue.
0 kommentar(er)
